For most productions, park in the Red lot, accessible from Tasman East of Great America Parkway, just past Convention Center Way, find the entrance on the right, often marked 49ers Store. Tell the gate attendant you are working. Park at the far end of available space towards the stadium, and enter security at the end of the Gate C Bridge. Meet at the AV shop or where assigned.
4900 Marie P. Debartolo Way, Santa Clara, California 95054, United States
check with your steward and plan to enter on Tasman from First Street. Come early to get through the blockades. Yellow lot passes are usually required to access the area and will allow you to park in the structure. Proceed to" Gate F" entrance.
All clothes should be clean, no tears or stains; shirts should be buttoned up, pants pulled up; no open toed shoes. Show Blacks for Set up, show and strike. Hard Hats during Opera set-up show and strike. High Vis for Symphony pushers.
Work Clothes: Jeans or other work pants; shorts or sleeveless shirts may not be acceptable in certain circumstances.
Show Blacks: Same as work clothes but black; jeans or cargo pants, small logos are acceptable.
Tech Blacks: Collared shirt (polo or button up), small logos may be acceptable; black jeans or Dockers; black shoes or sneakers.
Dress Blacks: Button up black shirt, no logos; black dockers or dress slacks, polished shoes.
Stage-Technicians
Flashlight
4 in 1 Screwdriver
Crescent Wrench
Multi-tool
Gloves
Rigger’s
Full Body Harness ANSI Z359
Y Lanyard ANSI Z359
80’ Rope 5/8” Single or Double Braid
Sheave
Multi Loop
Carabineers
Plumb Laser
Work Positioning Slings or Grillion
Fall Arrest Slings
Hard Hat with Chin Strap
Steel Builders
Steel Toe Boots
Hammer or 3 lb. Sledge
Podger- 19/22mm scaffold wrench
Crescent Wrench
Tower Climber’s
Full Body Harness ANSI Z359
Y Lanyard ANSI Z359
80’ Rope 5/8” Single or Double Braid
Sheave
Multi Loop
Carabineers
Work Positioning Slings or Grillion
Fall Arrest Slings
Hard Hat with Chin Strap
3 lb. Sledge w/ lanyard
Podger- 19/22mm scaff wrench w/ lanyard
Crescent Wrench
Carpenter’s Tool’s
Tool Belt
Tape Measure (30’-35’)
Hammer
4 in 1 Screw Driver
Screw Gun with Phillips Bit, Spare Battery and Charger
Crescent Wrench
Ratchet Wrench – 3/8″ drive, 3/8″, 7/16″, 1/2″, 9/16″ deep sockets
Channel Locks
Pliers
Vise Grips
Diagonal Cutters
Allen Set
Matt Knife
Flashlight
Safety Glasses
Gloves
Pen and Pencil
Black Sharpie
Audio Visual Tools
Flashlight
4 in 1 Screwdriver
Crescent Wrench
Multi-tool
Jewelers Screwdrivers – (Phillips and Flat)
Needle Nose Pliers
Assorted Nut Drivers
Pocket Knife
Circuit Tester
Board Tape or Masking tape
Electrical Tape
Sharpie or other fine point permanent marker
Gloves
Pen and small Pad of Paper
Electrician’s
Tape Measure
4 in 1 Screw Driver
Crescent Wrench
Ratchet Wrench – 3/8″ drive, 3/8″, 7/16″, 1/2″, 9/16″ deep sockets
Channel Locks
Pliers
Wire Cutters
Allen Set
Pocket Knife
Flashlight
Safety Glasses
Gloves
Pen and Pencil
Black Sharpie
OPTIONAL (but highly recommended):
Voltage Meter
Pin Splitter
Hard hats: ANZI Z89.1 compliant. Chin straps required for all climbers High Vis: Class 2 or 3
A Mask is recommended
Steel toe safety shoes and safety glasses (if you normally wear glasses are strongly recommended and are the responsibility of the technician.
*** Due to the COVID 19 Pandemic, there may be other employer requirements in place for this venue.
As of August 3rd, 2021 all workers will be required to wear a mask at all times, while indoors. This includes the 100 tunnel.
*** Due to the COVID 19 Pandemic, there may be other employer requirements in place for this venue.
Jon Curcio
Please log into IA 134's Call System for details about your call times.
If you have any questions please call the IA 134 Office at 408-294-1134 Ext 102
Copyright © 2023 IATSE LOCAL 134 - All Rights Reserved.